Sony Interactive Entertainment has confirmed that the PlayStation 5 will be getting expandable M.2 SSD storage support as part of the next major update. The expandable storage is currently available to users in the beta test program. Seagate has also confirmed that their FireCuda 530 range is PlayStation 5 ready, pricing on these drives are as follows:

  • 500GB with Heatsink – $159.99
  • 1TB with Heatsink – $259.99
  • 2TB with Heatsink – $549.99
  • 4TB with Heatsink – $999.99

Here’s what Jeff Park, country manager for Seagate Technology, had to say:

We have done some testing with Sony on the PlayStation 5 and today we can confirm that the FireCuda 530 with the heatsink has met all the PS5 requirements. With the PS5 design, the SSD card slot is very narrow, so there’s not much room for the SSD to mount. However, with the FireCuda 530 – even with the heatsink on the top – the slim design allows for it to fit. Of course, the FireCuda 530 without the heatsink is slimmer, so both of them will fit into the PS5.

Requirements via Sony Interactive Entertainment:

M.2 SSD requirements for PS5 consoles

Interface: PCIe Gen4 x4 M.2 NVMe SSD

Capacity: 250GB – 4TB

Cooling structure: Using an M.2 SSD with your PS5 console requires effective heat dissipation with a cooling structure, such as a heatsink. You can attach one to your M.2 SSD yourself, either in a single-sided format, or double-sided format. There are also M.2 SSDs that have cooling structures (such as heatsinks) built in.

Sequential read speed: 5,500MB/s or faster is recommended

Module width: 22mm width (25mm width is not supported)

Form Factor: M.2 type 2230, 2242, 2260, 2280 and 22110.
These numbers can be found on retail listings for M.2 SSD devices. The first two digits refer to the width, the remaining digits to the length.

Socket type: Socket 3 (Key M)

Total size including cooling structure:
In millimeters: smaller than 110mm (L) x 25mm (W) x 11.25mm (H).
In inches: smaller than 4.33in (L) x 0.984 in (W) x 0.442in (H).

See below for full requirements.

Length
The following M.2 SSD lengths are compatible with PS5 consoles:
30mm, 42mm, 60mm, 80mm, 110mm (corresponding to the form factor type, per above).

Width
A 22mm-wide M.2 SSD module is required.
The total structure (including an added cooling structure) cannot exceed 25mm (0.984in).

Height
The total height of the M.2 SSD and its cooling structure (such as a heatsink) – whether built-in or separate – must be less than 11.25mm (0.442in).
The height must also be in the right place, in relation to the M.2 SSD’s circuit board:

The size below the board must be less than 2.45mm (0.096in). The total size above the board must be less than 8mm (0.314in).
(Note: millimeter measurements are the technical standard and are more precise than inches. We recommend double-checking that the total dimensions of M.2 SSD and heatsink products you’re considering meet the millimeter requirements before purchasing)


– Both single-sided and double-sided M.2 SSD devices are supported.
– M.2 SATA SSDs aren’t supported.
– You should carefully review drive specifications prior to purchase and contact the vendor or manufacturer if you need further information. SIE cannot guarantee that all M.2 SSD devices meeting the described specifications will work with your console and assumes no responsibility for the selection, performance or use of third-party products.
– Not all games are necessarily playable with the exact same performance provided by the PS5 console’s internal Ultra-High Speed SSD, even where the M.2 SSD device’s sequential read speed is faster than 5500MB/s.
– The majority of M.2 SSD devices with the above type numbers (M Key Type 2230, 2242, 2260, 2280 and 22110) and without a built-in cooling structure will fit the PS5 console’s SSD slot. However, sizes for cooling structures (like heatsinks) vary greatly. If you are not sure an M.2 SSD or cooling structure (such as a heatsink) you’re considering meets the size requirements outlined here, we recommend looking for another product option or contacting the vendor or manufacturer for more information.
– If you experience problems while playing a game installed on M.2 SSD storage, move the game to the internal Ultra-High Speed console storage.

More information can be found here.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s